Special conical series for chamfering, folding and engraving plastics. Its helical geometry allows for perfect finishes on all types of plastic materials.

Carbide cutter with micro-polished helical helix that facilitates rapid chip ejection, leaving engraved surfaces clean and burr-free, both in plastics and non-ferrous metals. (*) References with D2 = 8 mm have a partially cylindrical cutting edge behind the conical edge, allowing for greater immersion depths (L2). Ideal for engraving and folding:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

- Aluminium and aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

GR9000 series with conical tip for ENGRAVING all types of materials. Except for stainless steel and ferrous metals.

Materials:

+ Plastic

+ Wood

+ Aluminium

The FIB8000 series is specially designed for cutting abrasive and fibre-loaded materials. The diamond-tip cutting edge design allows for efficient milling of the material's fibres and prevents delamination of the surface layers.

Recommended for cutting:

- Fibreglass (G10, G11, etc.)

- Carbon fibre.

- Other composite materials (aramid fibre, graphite, etc.).

Liquid diamond-coated tool with high performance that allows for perfect finishes, optimising the productivity of your CNC to the maximum, as its innovative design allows it to be used at extreme speeds of up to 40-50 m/min.

Materials:

+ MDF, melamine chipboard, plywood.

+ High-gloss finish panels, aluminium-coated panels, high-pressure laminates (HPL, Trespa®, Formica®), Bakelite.

The MORTISE series is characterized by its two downcut flutes. This milling cutter has a high ge­ometric stability and is mainly used for grooving and pocketing at high feed rates, also for cutting thin sheets and small parts. The downcut holds the material against the working table and allows for high quality surface finishes to be achieved.

Materials:

+ HPL

+ Softwoods

+ Hardwoods

+ Tropical woods

+ Phenolic plywood

+ MDF

+ Melamine chipboard

MC COMPRESSION is similar in geometry to D COMPRESSION, but MC has a coating that allows heat to be released from the cutting edge, thereby delaying wear on the cutter. Especially suitable for high production on melamine boards, MDF, plywood, etc.

Materials

+ Softwoods

+ Hardwoods

+ Tropical woods

+ Phenolic plywood

+ MDF

+ Melamine chipboard

Compression series developed with high wear resistance sub-micrograin carbide. It features highly optimised helix geometry and finishes for perfect chip evacuation, allowing it to be used at high feed rates. Its design is ideal for achieving perfect finishes free of delamination on the outermost layers in:

- Hard and soft woods.

- Plywood, MDF, melamine chipboard, OSB, etc.

- Solid surface materials: Corian®, Krion®, Varicor®, etc.

The ROMPEVIRUTAS (chip breaker) series is characterised by its special geometry, designed mainly for cutting HPL, Trespa or very hard materials. This continuous-edge cutter has a variable chipbreaker that leaves no marks, minimises vibrations during machining processes and dissipates heat thanks to its anti-abrasion coating.

Materials:

+ HPL

+ Trespa

+ Softwoods

+ Hardwoods

+ Tropical woods

+ Phenolic plywood

+ MDF

+ Melamine chipboard

The PCM100 series with high-density polycrystalline diamond inserts, highly resistant to wear and with a specific sharpening that allows for a very sharp edge, ideal for polishing and achieving cutting surfaces with a high level of shine or transparency, depending on the material of the workpiece.

The PCM100 series can polish with both the tool's side and tip.

Suitable for cutting and engraving:

- Thermoplastics: PMMA, PC, PVC, PP, PE, ABS, etc.

- Aluminium and other non-ferrous metals.

- Wood and wood derivatives (MDF, melamine chipboard, etc.).

PCD100 series, high-density polycrystalline diamond cutter with high wear resistance. Its design is highly stable, allowing high cutting performance when machining different materials such as:

- Wood and wood derivatives (MDF, melamine chipboard, etc.).

- High-pressure laminates (HPL), Bakelite, etc.

- Aluminium with high Si content and other non-ferrous metals.

- Carbon fibre, fibreglass, graphite, ceramic materials, etc.

Two- and three-flute carbide end mill designed to provide maximum rigidity and stability in metal machining. When cutting with this tool, the cutting forces are distributed evenly along the cutting edge, providing extra strength and preventing breakage even in low-power CNC centres. Ideal series for large engravings and cutting thin sheets in:

- Steel and stainless steel.

The FC7000 series has a geometry specially developed for machining foams. Mirror sharpening has been implemented to achieve an extremely sharp cutting edge that leaves exquisite finish surfaces. Virtually all references feature a neck for deep pocket machining. Suitable for cutting:

- Polyurethane (PUR) foams.

- Polyethylene (PE) foams.

- Foamed PVC.

The DC6000 series represents an innovation in non-ferrous metal machining. This series is designed to withstand abrasive effects and prevent aluminium from sticking to the cutting edge during machining:

- Hard and abrasive aluminium alloys.

- Soft aluminium alloys with a tendency to stick.

- Aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

AE6000 series with a multi-layer coating that provides low friction and high wear resistance. Our innovative coating allows any type of aluminium alloy to be machined, even dry, without the need for any lubrication.

-Aluminium.

- Aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

The AC6000 Series features micrograin carbide single-flute end mills specially designed for machining non-ferrous metals. They feature a very sharp cutting edge finished with an innovative tip geometry, developed specifically to facilitate immersion into the workpiece and improve chip ejection in soft aluminium, which tends to clog the tool during cutting.

To optimise performance, the use of lubricant during the cutting process is recommended.

Suitable for machining:

- Aluminium.

- Aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

Translated with DeepL.com (free version)

The BC5000 balanced cutting series features innovative geometry characterised by a mirror-finish micro-polished helix and a unique cutting edge design that enables stable, vibration-free cutting, even in machining conditions that require high feed rates and a depth of cut greater than 2 x D1.

Suitable for:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, PET, HDPE ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

The AB5000 series endmills are specially developed to achieve exceptional surface finish quality on thermoplastics, even when cutting at high feed rates.

This innovative geometry allows for optimal finishes in a single cutting pass on materials such as:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

3D1000 series hemispherical endmills with double-lip inserts made of ultra-fine grain carbide. Specially designed to achieve perfect surface finishes after the initial roughing process. New long references with a neck are included for machining operations requiring great depth.

Suitable for machining:

- Moulds and prototypes made of urethane, polyurethane resins, etc.

- Thermoplastics: PMMA, PVC, PP, PE, ABS, etc.

- Wood and wood derivatives: (MDF, melamine chipboard, etc.).

- Aluminium, copper, brass, zinc, etc.

Translated with DeepL.com (free version)

GPC4000 Series

GP4000 family series, endmills developed with greater overall length (L1), greater cutting length (L2) or with neck (L3). Ideal for the most demanding machining operations on:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

- Wood and wood derivatives (MDF, melamine chipboard, plywood, etc.).

The Micro2000 series endmills are manufactured from ultra-fine grain hard metal and designed with a highly stable geometry optimised for universal use. Suitable for cutting and engraving operations on:

- Thermoplastics: PMMA, PC, PVC, PP, PE, ABS, etc.

- Wood and wood derivatives (MDF, melamine chipboard, etc.).

- Aluminium and aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

The GPi4000 Series is the counterpart to the GP4000 but with a downcut. Maximum stability endmills when machining small, thin parts. It also improves finishes when the upper surface tends to delaminate.

These router bits feature an extremely sharp cutting edge and a micro-polished flute with a mirror finish, which effectively facilitates chip removal, reducing the risk of collapse or clogging of the cutter when machining plastic materials such as:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

- Wood and wood derivatives (MDF, melamine chipboard, plywood, etc.).

The Generica Pro series is a hard metal single lapped flute endmill, which allows for optimum quality in milling all types of plastic materials, woods and derivatives.

Its high versatility makes it an ideal choice for cutting:

Cast or extruded methacrylate.

PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

Solid surface materials: Corian®, Krion®, etc.

Wood and wood derivatives (MDF, melamine chipboard, plywood, etc.).

It is suitable for the purification of soot during laser marking, engraving, scribing, coding, manual soldering, dipping tin, manual repair of circuit boards, etc.

PC300 Fume Extractor with 300m3/h air flow and single freestanding arm.
220V,50HZ power. It has LCD display to show air flow and air pressure, air flow can be adjustable by both key switch and remote control, has warning system to remind customer to replace filters once blocked.

The LN 610 system, with its powerful and modular design, can function as a central extraction unit for several workstations at the same time. It is available in different versions (STANDARD, A, ZS and ZSA) and incorporates control electronics that facilitate its integration into automated processes.

Introducing the most advanced laser fume extractor: AD Oracle, which integrates multiple key features into one compact unit.

Its automatic voltage detection turbine works with any global voltage (110–220V). The reverse airflow system (bottom to top) optimises filter performance and extends its service life.

Automatic flow control allows the flow to be readjusted to reduce noise and protect both the combined filter and the DeepPleat DUO pre-filter, with 12 m² of filtering surface area.

·       Automatic voltage adaptation (90–257V)

·       Long-lasting filters and low replacement cost

·       Automatic flow control system

·       Filter status display

·       Compact and quiet design

Hose set DN 50 L: 1,25 m for LN/GL/FP/BF Serie, possibility to shorten to connect an extraction arm System 50 to the socket with an outside of Ø 50mm.

Comprising:

1 hose, 1.25 m (inner diameter 44 mm / outer diameter 50 mm), PVC, black.

1 screw-on coupling with an outer diameter of 50 mm.

1 screw-on coupling with an inner diameter of 50 mm.

White aluminium for sublimation 0,5mm

610x305x0,5mm

AC-Filter DUO, 730x300x280 mm

Version: metal cassette

filling: approx 60 liters specially impregnated activated carbon