There are 30 products.
Conical end mill with welded carbide inserts, specially designed for chamfering. Thanks to its geometry, this tool is highly efficient in machining:
- Thermoplastics: PMMA, PC, PVC, PP, PE, ABS, etc.
- Wood and wood derivatives (MDF, melamine chipboard, etc.).
- High-density foams.
Special conical series for chamfering, folding and engraving plastics. Its helical geometry allows for perfect finishes on all types of plastic materials.
Carbide cutter with micro-polished helical helix that facilitates rapid chip ejection, leaving engraved surfaces clean and burr-free, both in plastics and non-ferrous metals. (*) References with D2 = 8 mm have a partially cylindrical cutting edge behind the conical edge, allowing for greater immersion depths (L2). Ideal for engraving and folding:
- Cast or extruded methacrylate.
- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.
- Solid surface materials: Corian®, Krion®, etc.
- Aluminium and aluminium composites: Dibond®, Alucobond®, etc.
- Copper, brass, zinc, etc.
GR9000 series with conical tip for ENGRAVING all types of materials. Except for stainless steel and ferrous metals.
Materials:
+ Plastic
+ Wood
+ Aluminium
The FIB8000 series is specially designed for cutting abrasive and fibre-loaded materials. The diamond-tip cutting edge design allows for efficient milling of the material's fibres and prevents delamination of the surface layers.
Recommended for cutting:
- Fibreglass (G10, G11, etc.)
- Carbon fibre.
- Other composite materials (aramid fibre, graphite, etc.).
Liquid diamond-coated tool with high performance that allows for perfect finishes, optimising the productivity of your CNC to the maximum, as its innovative design allows it to be used at extreme speeds of up to 40-50 m/min.
Materials:
+ MDF, melamine chipboard, plywood.
+ High-gloss finish panels, aluminium-coated panels, high-pressure laminates (HPL, Trespa®, Formica®), Bakelite.
The MORTISE series is characterized by its two downcut flutes. This milling cutter has a high geometric stability and is mainly used for grooving and pocketing at high feed rates, also for cutting thin sheets and small parts. The downcut holds the material against the working table and allows for high quality surface finishes to be achieved.
Materials:
+ HPL
+ Softwoods
+ Hardwoods
+ Tropical woods
+ Phenolic plywood
+ MDF
+ Melamine chipboard
MC COMPRESSION is similar in geometry to D COMPRESSION, but MC has a coating that allows heat to be released from the cutting edge, thereby delaying wear on the cutter. Especially suitable for high production on melamine boards, MDF, plywood, etc.
Materials
+ Softwoods
+ Hardwoods
+ Tropical woods
+ Phenolic plywood
+ MDF
+ Melamine chipboard
Compression series developed with high wear resistance sub-micrograin carbide. It features highly optimised helix geometry and finishes for perfect chip evacuation, allowing it to be used at high feed rates. Its design is ideal for achieving perfect finishes free of delamination on the outermost layers in:
- Hard and soft woods.
- Plywood, MDF, melamine chipboard, OSB, etc.
- Solid surface materials: Corian®, Krion®, Varicor®, etc.
The ROMPEVIRUTAS (chip breaker) series is characterised by its special geometry, designed mainly for cutting HPL, Trespa or very hard materials. This continuous-edge cutter has a variable chipbreaker that leaves no marks, minimises vibrations during machining processes and dissipates heat thanks to its anti-abrasion coating.
Materials:
+ HPL
+ Trespa
+ Softwoods
+ Hardwoods
+ Tropical woods
+ Phenolic plywood
+ MDF
+ Melamine chipboard
The PCM100 series with high-density polycrystalline diamond inserts, highly resistant to wear and with a specific sharpening that allows for a very sharp edge, ideal for polishing and achieving cutting surfaces with a high level of shine or transparency, depending on the material of the workpiece.
The PCM100 series can polish with both the tool's side and tip.
Suitable for cutting and engraving:
- Thermoplastics: PMMA, PC, PVC, PP, PE, ABS, etc.
- Aluminium and other non-ferrous metals.
- Wood and wood derivatives (MDF, melamine chipboard, etc.).
PCD100 series, high-density polycrystalline diamond cutter with high wear resistance. Its design is highly stable, allowing high cutting performance when machining different materials such as:
- Wood and wood derivatives (MDF, melamine chipboard, etc.).
- High-pressure laminates (HPL), Bakelite, etc.
- Aluminium with high Si content and other non-ferrous metals.
- Carbon fibre, fibreglass, graphite, ceramic materials, etc.
