Beginning

Beginning

There are 344 products.

Showing 37-48 of 344 item(s)

Active filters

Endmills honeycomb cardboard

Microtoothed carbide milling cutter.

New series specially designed for cutting sandwich materials with core arranged in cells or honeycomb. Its compression geometry generates a burr-free finish at the top and bottom of the cut, and the innovative microdented propeller design allows crushing and prevents the detachment or "flagging effect" that takes place in the center of these materials when milled. Indicated for cutting of:

- Panels and graphic supports such as: Falcon Board®, BioBoardTM, Reboard® or other similar Honeycomb boards.

- Honeycomb aluminum panels.

- Sandwich panels with reinforced cores (Nomex®).

- Cellular polycarbonate.

PC800 extraction System

PC800 fume extractor:

Air flow rate: 800 m³/h (1360 CFM)

Pressure: 10,000 Pa

Power: 1.3 kW

Noise level: < 63 dBA

Weight: 86 kg

Dimensions: 500×562×1040mm

Inlet diameter: 100 / 125 mm

Voltage: 90–110 V / 210–257 V, single-phase, 50/60 Hz

Pre-filter: F9 deep-pleated filter (95% at 1.0 μm, ~20 m²)

Main filter: H14 deep-pleated filter (99.99% at 0.3 μm) + activated carbon (20 kg)

It features an LCD screen displaying airflow and air pressure; the airflow can be adjusted using either the switch or the remote control; it has an alert system to remind customers to replace the filters when they become blocked.

Conical end mills

Conical end mill with welded carbide inserts, specially designed for chamfering. Thanks to its geometry, this tool is highly efficient in machining:

- Thermoplastics: PMMA, PC, PVC, PP, PE, ABS, etc.

- Wood and wood derivatives (MDF, melamine chipboard, etc.).

- High-density foams.

Plastic engraving and folding

Special conical series for chamfering, folding and engraving plastics. Its helical geometry allows for perfect finishes on all types of plastic materials.

Carbide cutter with micro-polished helical helix that facilitates rapid chip ejection, leaving engraved surfaces clean and burr-free, both in plastics and non-ferrous metals. (*) References with D2 = 8 mm have a partially cylindrical cutting edge behind the conical edge, allowing for greater immersion depths (L2). Ideal for engraving and folding:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

- Aluminium and aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

Endmills for HPL-phenolic...

The ROMPEVIRUTAS (chip breaker) series is characterised by its special geometry, designed mainly for cutting HPL, Trespa or very hard materials. This continuous-edge cutter has a variable chipbreaker that leaves no marks, minimises vibrations during machining processes and dissipates heat thanks to its anti-abrasion coating.

Materials:

+ HPL

+ Trespa

+ Softwoods

+ Hardwoods

+ Tropical woods

+ Phenolic plywood

+ MDF

+ Melamine chipboard

PCD superfinish endmills

The PCM100 series with high-density polycrystalline diamond inserts, highly resistant to wear and with a specific sharpening that allows for a very sharp edge, ideal for polishing and achieving cutting surfaces with a high level of shine or transparency, depending on the material of the workpiece.

The PCM100 series can polish with both the tool's side and tip.

 

Suitable for cutting and engraving:

 

- Thermoplastics: PMMA, PC, PVC, PP, PE, ABS, etc.

 

- Aluminium and other non-ferrous metals.

 

- Wood and wood derivatives (MDF, melamine chipboard, etc.).

Endmill for aluminium...

The AC6000 Series features micrograin carbide single-flute end mills specially designed for machining non-ferrous metals. They feature a very sharp cutting edge finished with an innovative tip geometry, developed specifically to facilitate immersion into the workpiece and improve chip ejection in soft aluminium, which tends to clog the tool during cutting.

To optimise performance, the use of lubricant during the cutting process is recommended.

Suitable for machining:

 

- Aluminium.

- Aluminium composites: Dibond®, Alucobond®, etc.

- Copper, brass, zinc, etc.

Translated with DeepL.com (free version)

Endmills with a balanced cut

The BC5000 balanced cutting series features innovative geometry characterised by a mirror-finish micro-polished helix and a unique cutting edge design that enables stable, vibration-free cutting, even in machining conditions that require high feed rates and a depth of cut greater than 2 x D1.

Suitable for:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, PET, HDPE ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

Single flute endmills_downcut

The GPi4000 Series is the counterpart to the GP4000 but with a downcut. Maximum stability endmills when machining small, thin parts. It also improves finishes when the upper surface tends to delaminate.

These router bits feature an extremely sharp cutting edge and a micro-polished flute with a mirror finish, which effectively facilitates chip removal, reducing the risk of collapse or clogging of the cutter when machining plastic materials such as:

- Cast or extruded methacrylate.

- PC, PVC, foamed PVC, PP, PA, PE, ABS, etc.

- Solid surface materials: Corian®, Krion®, etc.

- Wood and wood derivatives (MDF, melamine chipboard, plywood, etc.).